Parametric optimization of abrasive water jet cutting for AA6063-3 wt. % TiC composites
Abstract
The present study aims to optimize the abrasive water jet processing parameters as machining aluminium metal matrix composites. Investigations were carried on 3 wt. % of TiC reinforce AA6063 composites produced by stir casting route. Taguchi methodology was used to explore the influence of abrasive waterjet parameters and their relations on the output responses. Material removal rate is greatly influenced by standoff distance, feed rate and abrasive flow rate respectively while surface roughness is highly influenced by abrasive flow rate, feed rate and standoff distance. The optimum parameter set in maximizing the material removal rate and minimizing the surface roughness is 100mm/min feed rate, 3mm standoff distance and 200g/min abrasive flow rate. The experimental results and optimization obtained give a technical record for industrial applications.
Downloads
References
2. Ahmadi, B.S.Y., Hassanzadeh, H. and Kahhal, P. (2007), Modeling of Single-Particle Impact in Abrasive Water Jet Machining, International Journal of Aerospace and Mechanical Engineering, V1, n4, pp. 233-238
3. Leeladhar Nagdeve, Vedansh Chaturvedi, Jyot Vimal (2012), Parametric optimization of abrasive waterjet machining using Taguchi methodology; International Journal of research in engineering and applied science, vol 2, issue 6.
4. Kolahan Farhad & Khajavi A.Hamid (2009), “A statistical approach for predicting and optimizing depth of cut in AWJ machining for 6063-T6 Al alloy”, World Academy of Science, Engineering and Technology, 59,441-45
5. M. Chithiraiponselvan and N. Mohanasundararaju (2012), Analysis of surface roughness in abrasive waterjet cutting of cast iron; International journal of science, environment and technology, vol. 1, no 3, 2012, 174 – 182.
6. Chirag M Parmar, Pratik K Yogi, Trilok D Parmar, 2014, Optimization of Abrasive Water Jet Machine Process Parameter for AL-6351 using Taguchi Method, International Journal of Advanced Engineering and Research Development, Volume 1, Issue 5,pp1-8.
7. R. Manu and N. Ramesh Babu, “Influence of jet impact angle on part geometry in abrasive waterjet turning of aluminium alloys”. Int. J. Machining and Machinability of Materials, Vol.3, Nos ½, 2008.
8. L. Chen, E. Siores, W.C.K. Wong, “Optimizing abrasive waterjet cutting of ceramic materials”. Journals of Materials Processing Technology 74 (1998) 251-154.
9. Sadaf Zahoor, Adeel. Shehzad, Keith Case, Amjad Hussain, Zain Zahoor and Muhammad Waqar Shoaib, 2017. Experimental investigation of surface roughness for different thickness of aluminium in abrasive waterjet machining, Proceedings of the Fifteenth International Conference on Manufacturing Research, University of Greenwich, London, UK, 5th-7th September 2017, pp. 9-14.
10. Ajit Dhanawade., Shailendra Kumar., 2017. Experimental study of delamination and kerf geometry of carbon epoxy composite machined by abrasive water jet. J. Compos. Mater. 51 (24), 3373-3390.
11. Azlan Mohd Zain, Habibollah Haron, Safian Sharif, “Genetic Algorithm and Simulated Annealing to estimate optimal process parameters of the abrasive waterjet machining”, Engineering with Computers, 2011, Vol. 27, pp 251–259.
Copyright (c) 2018 IJRDO - Journal Of Mechanical And Civil Engineering (ISSN: 2456-1479)
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Author(s) and co-author(s) jointly and severally represent and warrant that the Article is original with the author(s) and does not infringe any copyright or violate any other right of any third parties, and that the Article has not been published elsewhere. Author(s) agree to the terms that the IJRDO Journal will have the full right to remove the published article on any misconduct found in the published article.
