REVIEW OF JOURNAL BEARING OIL CLEARANCE AND LUBRICATION MANAGEMENT FOR TURBO GENERATORS
Abstract
The Review of Journal Bearing Oil Clearance and Lubrication Management for Turbo Generators is reported. The underlying tribological principles relating friction, wear and lubrication are considered. The dependence of lubricant film thickness on : Radial clearance between the leg journal and cone; Radius of the leg journal; Lubricant viscosity; Rotational velocity of the cone and Applied load is observed. The interplay between friction, wear and lubrication is observed.
Downloads
References
Nigerian Energy Support Programme (NESP) (2015), The Nigerian Energy Sector An
Overview with a Special Emphasis on Renewable Energy, Energy Efficiency and Rural Electrification 2nd Edition, June 2015 .* NESP is implemented by the Deutsche Gesellschaft für Internationale Zusammenarbeit (GIZ) GmbH and funded by the European Union and the German Federal Ministry for Economic Cooperation and Development (BMZ).
.2. The Nigerian Economic Summit Group and Heinrich Böll Stiftung Nigeria.(2017),
Comparison of Costs of Electricity Generation in Nigeria Abuja, June 2017. *The Lead Author is Maria Yetano Roche supported by Nnanna Ude and Ikenna Donald Ofoegbu, with inputs from stakeholders in the Nigerian power sector. Report was reviewer: Dr. Felix Matthes (Oeko Institute, Berlin) and Hans Verolme (Climate Advisers Network, Berlin).
Thomas H. Mccloskey (1995), trouble Shooting Bearing and Lube Oil System Problems.
https://oaktrust.library.tamu.edu-bitstream>handle.
Tribology - Wikipedia
https://en.wikipedia.org › wiki › Tribology
Tatjana Lazovic ,Aleksandar Marinkovic, S. Markovic (2011). A Case Study of TurboGenerator Journal Bearing Failure. Conference: BALKANTRIB 11, At Thessaloniki, Greece. October 2011.
Ilmar F. Santos, Russo F. H. (1998). Tilting-Pad Journal Bearings With Electronic Radial Oil Injection. Journal of Tribology. 120(3): 583. July 1998. DOI: 101115/1.2834591.
Hiromu Hashimoto (2007). Optimization of Oil Flow and Oil Film Temperature Rise in High Speed Hydrodynamic Journal Bearings in Tribology Series Vol.34, 1998, pp.205 - 219. In Tribology for Energy Conservation edited by: D. Dowson, C.M. Taylor, T.H.C. Childs, G. Dalmaz, Y. Berthier, L. Flamand, A.A. Lubrecht. Available online 11 October 2007. https://doi.org/10.1016/s0167-8922(98)80075-8
Wills W. Gardner (1998). Tilting Pad Thrust Bearing Tests - Influence of Oil Flow Rate On Power Loss and Temperatures in Tribology Series. Vol. 34, 1998, Pp. 211 - 217. https://doi.org/10.1016/s0167-8922(98)80076-x.
Authors links: Tribology Section, Department of Mechanical Engineering, Imperial College of Science, Technology & Medicine, London SW7 2BX, England.
Krupka I, Hartl M, Cermak J, Liska M (2007). Elastohydrodynamic Lubricant Film Shape - Comparison Between Experimental and Theoretical Results in Tribology Series. https://doi.org/10.1016/s0167 - 8922(98)80077-1
Chevalier F*, Lubrecht A.A., Cann P.M.E., Dalmaz G. (1998).The Evolution of Lubricant Film Defects in The Starred Regime in Tribology Series. Vol. 34. 1998. Pp. 233 - 242. https://doi.org/10.1016/s0167 - 8922(98)80078-3.
Ferguson J.H*J.H.Yuan**J.B.Medley**(2007). Spring-Supported Thrust Bearings For Hydroelectric Generators: Influence of Oil Viscosity on Power Loss *GE Hydro, Peterborough, ON K9J 7B5, Canada **Department of Mechanical Engineering, University of Waterloo, Waterloo, ON N2L 3G1, Canada. Tribology Series. Vol. 34. 1998. Pp. 187-194. Available online 11 October 2007.
https://doi.org/10.1016/S0167-8922(98)80073-4
Chao Zhang*, Zhming Zhang*, Zugan Qin**(1998). Analysis of mixed lubrication of dynamically loaded journal bearings including non-Newtonian effects and mass conserving cavitation in Tribology Series, Vol. 34. 1998. Pp. 175-186. https://doi.org/10.1016/S0167-8922(98)80072-2
*Tribology Group, University of Leed, UK.
Hamilton R.W. 1.Sayles1 R.S .Ioannides1 E 2Wear due to debris particles in rolling bearing contacts in Tribology Series. Volume 34, 1998, Pages 87-93 https://doi.org/10.1016/S0167-8922(98)80064-3
Hurley S .Cann P.M .Spikes H.A (1998). Thermal Degradation of Greases and the Effect on Lubrication Performance in Tribology Series. Volume 34, 1998, Pages 75-83. Available online 11 October 2007.. https://doi.org/10.1016/S0167- 8922(98)80063-1
HughSpikes (1994). Synthetic lubricants and high-performance functional fluids: Marcel Dekker, 1992, ISBN 0-8247-8715-3, 591 pp,
Available online 27 February 2003. Ed. R. L. Shubkin
https://doi.org/10.1016/0301-679X(94)90064-7.
Gregory F. Simmons (2013). Journal Bearing Design, Operation, Lubrication and Operation for Enhanced Performance. divaportal.org/smesh/get/diva23998958/FULL TEXT01.pdf.
Susumu Nakano,1 Tadaharu Kishibe,1 Tomoaki Inoue,2 and Hiroyuki Shiraiwa3
(2009). An Advanced Microturbine System with Water-Lubricated Bearings.
International Journal of Rotating Machinery. Volume 2009,
Cowlin F.J.* (1940). The Lubrication of Steam-Turbine Driven Electric Generators . Volume: 143 issue: 1, page(s): 83-100. First Published June 1, 1940 Research Article. https://doi.org/10.1243/PIME_PROC_1940_143_020_02 *Turbine Department, English Electric Company, Ltd., Rugby
Lyle A. Branagan* (2015). Survey of Damage Investigation of Babbitted Industrial Bearings Lubricants 2015, 3, 91-112; doi:10.3390/lubricants3020091 lubricants ISSN 2075- 4442 www.mdpi.com/journal/lubricants *Pioneer Motor Bearing Company, 129 Battleground Road, Kings Mountain, NC 28086, USA; E-Mail: lyleb@pioneer1.com; Tel.: +1-704-937-7000 (ext. 118); Fax: +1-704-937-9429. . Academic Editors: Romeo P. Glovnea and Michel Fillon Published: 1 April 2015
PRADEEP B . SIVA. Bearing design for Turbo Generator- Internship at BHEL
Dana J. Salamone*. Journal Bearing Design Types and Their Applications to Turbomachinery in the Proceedings of the 12th Turbo machinery Symposium *Chief Engineer, Centitech Corporation, Houston, Texas. pdfs.semanticscholar.org/e2gd/cba4fd78baafd07788e001217e70ec8.pdf
Malcolm E. Leader, P.E.(2019) Understanding Journal Bearings. Applied Machinery Dynamics Co. Durango, Colorado
Uzochukwu E, Nwosu H.U., Major I.E. (2013) Mechanics and Dynamics of Machinery. P.82. Springfield Publishers. Owerri, Nigeria. ISBN: 978-978-8500-11-7.
Copyright (c) 2020 IJRDO - Journal Of Mechanical And Civil Engineering (ISSN: 2456-1479)
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
Author(s) and co-author(s) jointly and severally represent and warrant that the Article is original with the author(s) and does not infringe any copyright or violate any other right of any third parties, and that the Article has not been published elsewhere. Author(s) agree to the terms that the IJRDO Journal will have the full right to remove the published article on any misconduct found in the published article.
